|
|
|
|
|
|
 |
Equivalent dynamic load |
| |
Date:2008-06-27 14:18:09Click:0Comment:0  |
| Bearings usualy carry the combination of radial load and axial load,and the load conditions are varied, and the load conditions are caried. such as the changes in the amount and so on. Therefore, the actual load can not be directly compared with its |
|
|
Basic dynamic load rating |
| |
Date:2008-06-27 11:13:58Click:0Comment:0 |
| Basic dynamic load rating indicates the fatigue resistant capacity (i.e.load carrying capacity). It shows that with pure radial load (for radial bearings) or axial load (for thrust bearings) of certain amount and direction, and with the presumption |
|
|
Life of bearing |
| |
Date:2008-06-27 09:49:42Click:0Comment:0 |
| When the bearing is carrying load,material fatigue shall happen even under normal operating conditionsdue to the effects of changing load on the raceways of rings and the sliding surface of the rolling elements,and if will canse scaling damage on of |
|
|
Introduction to selection of bearings |
| |
Date:2008-06-04 08:56:00Click:0Comment:0 |
| The varicty in kinds and types and dimensions of bearings makes the selection of the most appropriate bearings very important in order to achieve the expected functions of the mechanical devices. Analyses and evaluations from different viewpoints on |
|
|
Thrust taper roller bearings |
| |
Date:2008-06-03 15:04:54Click:0Comment:0 |
| The tapered rollers (with larger spherical end) of these bearings are guided precisely by the integral flanges of the washers (shaft washer and housing washer) with raceways.. When extended,the design makes the tapered raceway surfaces of the Shaft |
|
|
The use conditions and the surrounding conditions of the bearings |
| |
Date:2008-06-03 11:03:31Click:0Comment:0 |
| Correct definitions on the application position in the mechanical device and the use conditions and surrounding conditions are the pre-conditions of choosing the proper bearing For this purpose.the following figures and data are required. (1) The fu |
|
|
Structures of taper roller bearings |
| |
Date:2008-05-24 09:29:05Click:0Comment:0 |
| single-row taper roller bearings These bearings can only limit the axial movement of either the shaft or the houusing in one direction, and can carry axial load in one direction. When with only radial load, the axial forct two of the bearings be put |
|
|
The selection of bearing collocation |
| |
Date:2008-05-10 11:02:47Click:0Comment:0 |
| Normally , the shaft is supported by twobearings in radial and axial directions. Then, one of the bearings is called the fixing-end bearing which carries the load in radial an axial directions.Ie congrols the comparative axial movement between the s |
|
|
Taper roller bearings |
| |
Date:2008-05-10 10:32:45Click:0Comment:0 |
| These bearings have tapered ropered rollers which are guided by the thickr side of the cup.The design of the sliding surfaces of the cup and inner and the rolling elements when extended con nerge towards the same single point on the bearing axle. Si |
|
|
Cylindrcal roller bearings |
| |
Date:2008-05-10 09:44:21Click:0Comment:0 |
| Cylindrical rollers have linear contact with the raceway , and the bearings can carry heavier radial load . Applicatiins are foundin situations characterized by heavy load and alsohigh rotation speed. The N type and NU type bearings can be movable a |
|
|
Thrust ball bearings |
| |
Date:2008-05-10 09:18:29Click:0Comment:0 |
| Bearings of type consist of washers with raceway and the assembly of balls and cage. The washer that contactcts the shaft is called shaft washer, and the one attached to the housing is calledthe housing washer. Thrust bearings in double directions h |
|
|
Angular contact ball bearings for paired mounting |
| |
Date:2008-05-10 08:53:16Click:0Comment:0 |
| Based on the side face configuration, the angular contact ball bearings for paired mounting can be divided into three groups: 1.Back-to-back arrangement: 2.face-to-face arrangement: 3.Tandem arrangement: These bearings can carry the combination of a |
|
|
Deep groove ball bearings |
| |
Date:2008-05-10 08:00:38Click:0Comment:0 |
| They are the most typical rolling bearings bearings with extensiveapplications. The raceways in both of the rings are in arcgroove form, which can carry radial load and axial load indouble directions. They can be applied in situations wherehigh-rota |
|
|
Basic dynamic load rating of bearing |
| |
Date:2008-04-25 07:48:55Click:0Comment:0 |
| Basic dynamic load rating indicates the fatigue resistant capacity(i.e.load carrying capacity). It shows that with pure radial load (for radial bearings) or axial load (for thrust bearings) of certain amount and directiaon, and with the presumption |
|
|
|
|
|
|
Copyright 2008 © Wafangdian PengLi Bearing Manufacturing Co., Ltd. All rights reserved. Power by Newtwowin
|
|
